![\"clear](\"https:\/\/www.carpaintrepairinfo.com\/wp-content\/uploads\/2011\/10\/clear_coat_scratch12.jpg\")
<\/a><\/figure>\n\n\n\nMost car scratches only go into the clear coat, but don’t gouge into the paint layer.\u00a0 These kinds of scratches can be caused by bushes, tree branches, keys, and fingernails around the door handle, drive-through car wash, etc. <\/p>\n\n\n\n
Light clear coat scratches can be easily fixed with some good quality rubbing compound. Medium to deep clear coat scratches require some sanding.<\/p>\n\n\n\n
This blue-gray Pontiac had a medium clear coat scratched. To remove it, the body shop would take the same steps I am outlining below. The whole repair should take you about 15 min.<\/p>\n\n\n\n
Items You’ll Need:<\/h2>\n\n\n\n\n- Wet\/dry 2,000 grit sandpaper<\/a><\/li>\n\n\n\n
- Prep solvent<\/a>\u00a0\u2013 It removes oils, road grease, dirt, car wax, and other surface contaminants and also improves adhesion to the surface.<\/li>\n\n\n\n
- Meguiar\u2019s Ultimate Compound<\/a>\u00a0\u2013 You can use any rubbing compound you like, just make sure it is clear coat safe.\u00a0Meguiar\u2019s Ultimate Compound<\/em>\u00a0is the\u00a0best car scratch remover<\/a>\u00a0I\u2019ve ever tried. It removes light-to-deep clear coat scratches, swirl marks, stains, and heavy oxidation in just a few minutes. It\u2019s clear coat safe and inexpensive.<\/li>\n\n\n\n
- Applicator Pads<\/a>\u00a0\u2013 These pads are used to apply rubbing compound, polish, and wax.<\/li>\n<\/ul>\n\n\n\n
Optional Items:<\/strong><\/p>\n\n\n\n\n- Meguiar\u2019s Ultimate Polish <\/a>\u2013 Use your favorite polishing compound. I like Meguiar\u2019s Ultimate Polish because it uses diminishing abrasive technology, meaning the tiny abrasives break down gradually as you rub. The paint color will look bolder and brighter with a smooth, sleek shine. It is high quality, inexpensive, long-lasting, and clear coat-safe.<\/li>\n\n\n\n
- Meguiar\u2019s Tech Wax<\/a> \u2013 Use your favorite wax. I like Meguiar\u2019s NXT Generation Tech Wax. This product is amazing because not only does it give the deepest and clearest shine you\u2019ve ever seen, but it also acts as a paint sealer giving your car long-lasting protection.<\/li>\n\n\n\n
- Microfiber Towel<\/a>\u00a0\u2013 Avoid using other materials such as bath towels, paper towels, or washcloths, as they might leave scratches on the clear coat.<\/li>\n\n\n\n
- Dual Action Sander\/Polisher<\/a>\u00a0\u2013 I found a nice beginner polisher on Amazon for a reasonable price that will give you amazing results. There are a lot of professional polishers, but they cost over $200. This Black & Decker polisher got great customer reviews.<\/li>\n<\/ul>\n\n\n\n
Note: <\/strong>When it comes to car paint repair products, I use a lot of\u00a0 Meguiar’s products, because they always deliver high-quality jobs, are very inexpensive, and are easy to use. But you can use any products you like. <\/p>\n\n\n\nThe only thing that I recommend is, if you are not sure how well different brand products work together, stick to one brand throughout the whole process. The same brand products are specifically made to work with each other, therefore you’ll have better results.<\/p>\n\n\n\n
Step 1: Wash and Dry your car<\/h2>\n\n\n\n
Use special auto detergent or dish soap to remove wax, oil, and grease from the repair area. Follow it with prep solvent. It’s very important to start with a clean area for successful paint repair. When done washing, dry it completely with a soft towel or allow it to air dry.<\/p>\n\n\n\n
Step 2: Sanding Clear Coat<\/h2>\n\n\n\n
Sand the scratch with wet\/dry 2,000-grit sandpaper. I like using wet sanding more than dry sanding because it cuts faster. Soak sandpaper in cold water for 10 min. Spray the area with water and gently sand the scratch. Your goal is to even out the surface without sanding through the clear coat.<\/p>\n\n\n\n![\"deep](\"..\/wp-content\/uploads\/2011\/10\/clear_coat_scratch24.jpg\" "\\"clear_coat_scratch2\\"\/")
<\/figure>\n\n\n\n![\"sanding](\"..\/wp-content\/uploads\/2011\/10\/clear_coat_scratch33.jpg\" "\\"clear_coat_scratch3\\"\/")
<\/figure>\n\n\n\nRemove dust after each round of sanding. Check with your fingers for smoothness. If you start seeing paint color on your sandpaper, that means you are sanding too much. The white matter in the photo below looks like some kind of paste, but really it is just dust from clear coat sanding mixed with water. <\/p>\n\n\n\n
It might take you a few rounds of sanding and cleaning the area to get the surface even. After you are done sanding, clean the surface. Don’t be concerned about the area looking dull. Those sand scratches will be easily removed in the next step.<\/p>\n\n\n\n![\"scratch](\"..\/wp-content\/uploads\/2011\/10\/clear_coat_scratch92.jpg\" "\\"clear_coat_scratch9\\"\/")
<\/figure>\n\n\n\nStep 2: Rubbing Compound<\/strong><\/h2>\n\n\n\nUse a rubbing compound<\/a> to get rid of sand scratches. Apply a small amount of rubbing compound on a clean applicator pad. Rub over scratch using a firm circular motion until the rubbing compound is dry.<\/p>\n\n\n\n![\"Applying](\"..\/wp-content\/uploads\/2011\/10\/clear_coat_scratch43.jpg\" "\\"clear_coat_scratch4\\"\/")
<\/figure>\n\n\n\nStep 3: Remove Residue <\/h2>\n\n\n\n
Remove remaining product with a clean microfiber cloth![\"\"](\"http:\/\/www.assoc-amazon.com\/e\/ir?t=carpaintrepair-20&l=as2&o=1&a=B0009IQZH0\")
using circular motion with a lot of pressure. Avoid using other materials such as bath towels, paper towels, or washcloths since they are too rough and might leave scratches on the clear coat.<\/p>\n\n\n\n![\"wipe](\"..\/wp-content\/uploads\/2011\/10\/clear_coat_scratch63.jpg\" "\\"clear_coat_scratch6\\"\/")
<\/figure>\n\n\n\nStep 4: Polish the Area<\/h2>\n\n\n\n
Now that the scratch is gone, the surface is a little dull. Use polishing compound to restore the shine. Apply a small amount of polishing compound to a clean microfiber pad and polish the area for 1 to 2 minutes with circular motions. This will restore the shine and provide paint protection.<\/p>\n\n\n\n
Although polishing can be done by hand, you will get a better and faster result when using a buffing\/polishing machine. I found a nice beginner dual action polisher<\/a> on Amazon for a reasonable price that will give you amazing results.<\/p>\n\n\n\n![\"applying](\"..\/wp-content\/uploads\/2011\/10\/clear_coat_scratch53.jpg\" "\\"clear_coat_scratch5\\"\/")
<\/figure>\n\n\n\nStep 5: Wax Your Car<\/h2>\n\n\n\n
You are almost done. Apply your favorite wax<\/a> using a buffer or by hand.<\/p>\n\n\n\nFinal Result:<\/h2>\n\n\n\n
Optional Items:<\/strong><\/p>\n\n\n\n Note: <\/strong>When it comes to car paint repair products, I use a lot of\u00a0 Meguiar’s products, because they always deliver high-quality jobs, are very inexpensive, and are easy to use. But you can use any products you like. <\/p>\n\n\n\n The only thing that I recommend is, if you are not sure how well different brand products work together, stick to one brand throughout the whole process. The same brand products are specifically made to work with each other, therefore you’ll have better results.<\/p>\n\n\n\n Use special auto detergent or dish soap to remove wax, oil, and grease from the repair area. Follow it with prep solvent. It’s very important to start with a clean area for successful paint repair. When done washing, dry it completely with a soft towel or allow it to air dry.<\/p>\n\n\n\n Sand the scratch with wet\/dry 2,000-grit sandpaper. I like using wet sanding more than dry sanding because it cuts faster. Soak sandpaper in cold water for 10 min. Spray the area with water and gently sand the scratch. Your goal is to even out the surface without sanding through the clear coat.<\/p>\n\n\n\n Remove dust after each round of sanding. Check with your fingers for smoothness. If you start seeing paint color on your sandpaper, that means you are sanding too much. The white matter in the photo below looks like some kind of paste, but really it is just dust from clear coat sanding mixed with water. <\/p>\n\n\n\n It might take you a few rounds of sanding and cleaning the area to get the surface even. After you are done sanding, clean the surface. Don’t be concerned about the area looking dull. Those sand scratches will be easily removed in the next step.<\/p>\n\n\n\n Use a rubbing compound<\/a> to get rid of sand scratches. Apply a small amount of rubbing compound on a clean applicator pad. Rub over scratch using a firm circular motion until the rubbing compound is dry.<\/p>\n\n\n\n Remove remaining product with a clean microfiber cloth Now that the scratch is gone, the surface is a little dull. Use polishing compound to restore the shine. Apply a small amount of polishing compound to a clean microfiber pad and polish the area for 1 to 2 minutes with circular motions. This will restore the shine and provide paint protection.<\/p>\n\n\n\n Although polishing can be done by hand, you will get a better and faster result when using a buffing\/polishing machine. I found a nice beginner dual action polisher<\/a> on Amazon for a reasonable price that will give you amazing results.<\/p>\n\n\n\n You are almost done. Apply your favorite wax<\/a> using a buffer or by hand.<\/p>\n\n\n\n\n
Step 1: Wash and Dry your car<\/h2>\n\n\n\n
Step 2: Sanding Clear Coat<\/h2>\n\n\n\n
<\/figure>\n\n\n\n<\/figure>\n\n\n\n<\/figure>\n\n\n\nStep 2: Rubbing Compound<\/strong><\/h2>\n\n\n\n
<\/figure>\n\n\n\nStep 3: Remove Residue <\/h2>\n\n\n\n
<\/figure>\n\n\n\nStep 4: Polish the Area<\/h2>\n\n\n\n
<\/figure>\n\n\n\nStep 5: Wax Your Car<\/h2>\n\n\n\n
Final Result:<\/h2>\n\n\n\n